VMWARE WINDOWS 2000 ISO HOW TO
VMWARE WINDOWS 2000 ISO INSTALL
VMWARE WINDOWS 2000 ISO DRIVERS
VMWARE WINDOWS 2000 ISO PATCH

Newguest # nc -l -p 9000 | | dd of=/dev/vda bs=1M If you want to use compression anyway, pipe the data streams through the compression programs: oldguest # dd if=/dev/sda bs=1M | | nc 9000 High compression programs like bzip2 or xz will use 100% of a virtual processor anyway and hence limit the reading rate to 2/3 MB/s. We skip the compression of the data before sending it over the network as the bandwidth of the network was higher than the speed of the slowest virtual disc. After the transfer is complete, you can abort netcat on one machine вЂ“ the other netcat command will also exit. Compare the results of the dd progress on both machines, to make sure everything was received properly on the new guest. Go to the console where you started dd to see the results. This sends a signal to all dd processes to output their progress stats to stdout. To check the progress on the receiver side, you can use: newguest # killall -USR1 dd DonвЂ™t abort the command immediately after the transfer has finished, because some data might sill be left in the sending queue of nc. Instead you can watch the stats of dd in the console. Note: nc does not return when dd has finished. This time the command works vise-versa: Diskdump reads from the local virtual hard disk and pipes the data stream to netcat which sends the data to the new guest: oldguest # dd if=/dev/sda bs=1M | nc 9000 The hard disk of the old guest on the ESXi 5.0 System has the name /dev/sda. Now you can start the copy process on the old machine. As ifconfig is obsolete, we use the ip tool from the iprout2 package: newguest # ip addr Therefore the ip address of the new guest is needed. The next step is to start reading the old hard disk and send it to the new guest. If you want to copy only the system partition, make sure that you create the partitions on the new disc with a Windows installation medium. The old Windows bootloader cannot handle this. Newer tools try to align the partition to the blocks of the disk to optimize for SSDs. The boot loader of Windows 2000/XP/2003 Server does not allow any other partition format as done by the Windows installer. Note: Be sure to copy the whole disk and not only the partitions. The blocksize of 1 MB is to reduce overhead caused by the default of 4 KB that results in many small write requests. Everything that is received by netcat will be piped to diskdump, which copies the data stream to the hard disk: newguest # nc -l -p 9000 | dd of=/dev/vda bs=1M Next step is to start a netcat process listening on port 9000. With the default settings they use a para-virtualized hard disk, which will show up as /dev/vda. Check out the device name of the hard disk. When both systems are up showing the root prompt # and both have a working network connection, you can start with the new guest on the Ganeti cluster.

VMWARE WINDOWS 2000 ISO HOW TO

There are many sources on the internet about how to configure ESXi to boot from a CD, so we will skip this part.ДЄfter the linux boot cdвЂ™s has started, use the ESXi Client to connect to the old machine and VNC to connect to the new one. To set the boot cd in Ganeti, use: newvhost # gnt-instance modify -H boot_order=cdrom,cdrom_image_path='/path/to/image.iso' ДЇurther make sure that VNC is running on this machine: newvhost # gnt-instance modify -H vnc_bind_address=0.0.0.0 To do so, the Gentoo based System Rescue CD can be used to boot both systems and access the data. To avoid a time consuming procedure of exporting, converting and importing, the disk can be copied directly over the network. After installing the raw-image, the new instance can be created as follows: newvhost # gnt-instance add -t drbd -o raw-image+default -s 55g -B vcpus=4,memory=4096 An empty Ganeti template can be found at SourceForge. Next, a new machine must be created on the destination host. In doing so, the para-virtualized devices in KVM could be used from the begin on.

VMWARE WINDOWS 2000 ISO DRIVERS

Installing the Virt IO drivers before moving the virtual machine could also work nicely but was not tested so far. Windows 7/Windows 2008 Server and higher is not affected by this issue. This concerns mainly Windows XP flavored systems.

VMWARE WINDOWS 2000 ISO INSTALL

Just follow the instruction of the knowledge base article to install the registry patch.

VMWARE WINDOWS 2000 ISO PATCH

Hence before shutting down the virtual machine, you have to install this registry patch available from the Microsoft Knowledge Base. Before we start, it is important to know that without the appropriate modifications to the registry, a Windows 2000/XP/2003 Server refuses to boot from a new disk controller.

Vmware windows 2000 iso